ความจำเป็นในการติดฟิล์มป้องกันบนโปรไฟล์อลูมิเนียม
ความจำเป็นในการติดฟิล์มป้องกันบนโปรไฟล์อลูมิเนียม
ความจำเป็นในการติดฟิล์มป้องกันบนโปรไฟล์อลูมิเนียม
ความจำเป็นในการติดฟิล์มป้องกันบนโปรไฟล์อลูมิเนียม, ฟิล์มป้องกันเป็นวัสดุฟิล์มชนิดหนึ่งที่มีฟังก์ชั่นป้องกันพื้นผิว, และยังเป็นหนึ่งในผลิตภัณฑ์ที่สำคัญที่สุดในกาวที่ไวต่อแรงกด (PSA).
The protective film is usually made of polyolefin plastic film as the base material and acrylic polymer as the base resin of the pressure-sensitive adhesive, which is processed by a coating machine.
The real meaning of the protective film is a temporary protective measure taken to prevent surface scratches during the storage, transportation and circulation of goods, or between the processing steps of the substrate.
The protective film is widely used in the surface protection of aluminum panels, aluminum-plastic composite panels, mirror steel plates, color panels, plexiglass panels, decorative panels, aluminum profiles, plastic steel profiles, stainless steel coils, marble materials and display screens.
The protective film for aluminum profile is based on a polyethylene (PE) ฟิล์มที่มีสูตรเฉพาะ, กรดโพลีอะคริลิก (เอสเทอร์) เรซินถูกใช้เป็นวัสดุหลักของกาวไวต่อแรงกด, และมีการเคลือบกาวเฉพาะหลายชนิด, กรีด, และแปรรูปในบรรจุภัณฑ์และกระบวนการอื่นๆ.
ฟิล์มป้องกันมีความนุ่มนวลโดยธรรมชาติ, ยึดเกาะได้ดี, ติดง่าย, และลอกออกได้ง่าย. กาวไวต่อแรงกดมีความเสถียรที่ดีและจะไม่ส่งผลเสียใดๆ ต่อพื้นผิวของโปรไฟล์อลูมิเนียมที่จะถ่ายทำ.
1. ลักษณะโครงสร้างและวัสดุของฟิล์มป้องกัน
ฟิล์มป้องกันโดยทั่วไปจะเป็นฟิล์มป้องกันชนิดโพลีอะคริเลต.
โครงสร้างพื้นฐานของฟิล์มป้องกันชนิดโพลีอะคริเลต (รูป 1): จากบนลงล่าง: ชั้นแยก; ชั้นการพิมพ์; ฟิล์ม; ชั้นกาว.
1. ชั้นแยก;2.ชั้นการพิมพ์;3.ฟิล์ม;4.ชั้นกาว
โครงสร้างของฟิล์มป้องกันโปรไฟล์อลูมิเนียมชนิดโพลีอะคริเลต
1.1 ฟิล์ม
โดยทั่วไปฟิล์มจะใช้โพลีเอทิลีนความหนาแน่นต่ำ (PE) และโพลีไวนิลคลอไรด์ (พีวีซี) เป็นวัตถุดิบ.
สามารถรับได้โดยการอัดขึ้นรูป, การฉีดขึ้นรูป, และการเป่าขึ้นรูป.
เพราะโพลีเอทิลีนมีราคาถูกกว่าและเป็นมิตรกับสิ่งแวดล้อมมากกว่า, 90% ของฟิล์มทำจากโพลีเอทิลีน, โดยการเป่าขึ้นรูปเป็นหลัก.
โพลีเอทิลีนมีหลายประเภท, มีจุดหลอมเหลวและความหนาแน่นต่างกัน.
1.2 กาว
สิ่งสำคัญในคุณภาพของฟิล์มป้องกันนั้นพิจารณาจากลักษณะของคอลลอยด์.
มีกาวไวต่อแรงกดสองชนิดที่ใช้ในฟิล์มป้องกัน: กาวโพลีอะคริเลตที่ใช้ตัวทำละลายและกาวโพลีอะคริเลตที่ละลายน้ำได้, ซึ่งมีลักษณะที่แตกต่างกันออกไป.
1.2.1 กาวโพลีอะคริเลตที่ใช้ตัวทำละลาย
Solvent-based polyacrylate glue uses organic solvents as a medium to dissolve acrylic monomers.
The colloid is very transparent, has a relatively low initial viscosity, and is very resistant to aging.
It can last up to 10 แม้ว่าเทคนิคการผลิตจะไม่เปลี่ยนแปลงไปมากนัก, when exposed to ultraviolet rays, the colloid will slowly Cure.
After the film is corona treated, the polyacrylate glue can be directly coated without primer.
Polyacrylate glue is hard and has poor fluidity, so the adhesion of the protective film is slower.
Even after pressure, the glue and the surface to be attached cannot be fully contacted.
After being placed for 30 เครื่องขัดขี้เลื่อยอลูมิเนียมของเราใช้ได้ทั้งขยะขาวและดำ 60 สามารถใส่อะไหล่เสริมเข้ากับเครื่องได้, it will fully contact the surface to achieve final adhesion, And the final viscosity is often 2 ~ 3 times larger than the viscosity of the paste, if the viscosity of the protective film is suitable for the cutting, the end-user may be very laborious when tearing the film, or even cannot be torn off.
1.2.2 Water-soluble polyacrylate glue
Water-soluble polyacrylate glue uses water as a medium to dissolve acrylic monomers, and basically has the characteristics of solvent-based polyacrylate glue, but the glue should avoid and reduce contact with water and air to avoid residual glue.
Since water-soluble polyacrylate glue is more environmentally friendly and does not require a solvent recovery device, this glue is often used to produce protective films in developing countries.
1.3 Characteristics of adhesive
1.3.1 Adhesion
Refers to the force required to peel the protective film from the surface to be attached after a period of time.
Adhesion is related to the material to be attached, pressure, ระยะเวลาในการติดฟิล์ม, มุมและอุณหภูมิในการฉีกฟิล์ม.
โดยทั่วไป, ด้วยเวลาและความกดดันที่เพิ่มขึ้น, การยึดเกาะก็จะเพิ่มขึ้นเช่นกัน, และความหนืดของฟิล์มป้องกันไม่ควรเพิ่มขึ้นมากเกินไปเพื่อให้แน่ใจว่าไม่มีกาวตกค้างเมื่อฟิล์มฉีกขาด. โดยทั่วไป, ใช้การทดสอบการลอกแบบ 180 องศาเพื่อวัดการยึดเกาะ.
1.3.2 การติดต่อกัน
หมายถึงความแข็งแรงของกาวด้านใน.
การทำงานร่วมกันของคอลลอยด์ในฐานะฟิล์มป้องกันจะต้องสูงมาก, มิฉะนั้น, เมื่อฟิล์มกันรอยถูกฉีกออกจากกัน, ด้านในของคอลลอยด์จะแตกร้าวและทำให้เกิดกาวตกค้าง.
วิธีการวัดการทำงานร่วมกัน: ติดฟิล์มป้องกันบนพื้นผิวสแตนเลส, และแขวนน้ำหนักไว้บนฟิล์มป้องกันเพื่อวัดว่าต้องใช้เวลานานเท่าใดในการดึงฟิล์มป้องกันออกตามน้ำหนัก.
ถ้าแรงยึดเกาะมากกว่าแรงยึดเกาะ, ฉีกฟิล์มป้องกันออก, และพันธะระหว่างโมเลกุลของกาวจะแตกตัวและทำให้เกิดกาวตกค้าง.
1.3.3 แรงยึดเหนี่ยว
หมายถึงแรงยึดเกาะของกาวและฟิล์ม. ถ้าแรงยึดเกาะมากกว่าแรงยึดเกาะ, ฉีกฟิล์มป้องกันออก, พันธะระหว่างโมเลกุลของกาวกับฟิล์มก็จะขาดหายไป, ทำให้เกิดกาวตกค้าง.
1.3.4 ทนต่อรังสียูวี
กาวโพลีอะคริเลตมีความทนทานต่อรังสียูวี. หลังจากเติมฟิล์มป้องกันกาวโพลีอะคริเลตโปร่งใสพร้อมสารกันยูวีแล้ว, ความต้านทานรังสียูวีสามารถเข้าถึงได้ 3 เครื่องขัดขี้เลื่อยอลูมิเนียมของเราใช้ได้ทั้งขยะขาวและดำ 6 เดือน.
โดยทั่วไป, อุปกรณ์จำลองสภาพอากาศใช้เพื่อทดสอบความต้านทานรังสียูวีของฟิล์มป้องกัน.
มีการปรับอุณหภูมิและความเข้มของรังสี และใช้น้ำควบแน่นเพื่อเลียนแบบการเปลี่ยนแปลงสภาพภูมิอากาศ.
ทั้งหมด 3 ชั่วโมงของสภาพแวดล้อมที่มีความชื้นสูงและ 7 hours of ultraviolet radiation is a cycle, and a 50-hour cycle experiment is equivalent to approximately leaving it outdoors for a month.
2. Production of protective film
2.1 Production of protective film
In the heated drum, the polyethylene particles are pushed by the screw to the round die head, compressed air will blow the molten liquid, through the air cooling, rolled into a film.
The properties of blown film in the transverse and longitudinal directions are different. The elongation in the machine direction of the protective film is generally greater than 180%, and the elongation in the transverse direction is generally greater than 380%.
T ของสายการผลิตการอัดรีดโปรไฟล์อลูมิเนียม, the elongation is inversely proportional to the mechanical strength.
If the elongation is too large (such as greater than 500%), the mechanical strength of the film will often be very low, which will easily cause the protective film to be damaged during transportation and handling, and when unwinding, the protective film is easily stretched, after cutting, the protective film will rebound and warp.
2.2 Coating of adhesive
The corona-treated film can be directly coated with polyacrylate glue, no primer is required.
Then the protective film passes through a long air heating channel (80 ~ 120°C) to ensure that the water or solvent is evaporated, and then the protective film is cooled by a cooling roller, and finally rolled up.
2.3 Rewinding, slitting and storage
The protective film is directly rewound on the coating machine to the length required by the customer.
If the customer needs the protective film to have a beautiful appearance and no bubble wrap, it can be rewinded with a high-quality rewinder to ensure that there is no air wrap.
For short protective film (under 500 เมตร), a straight knife can be used for slitting. Over 500 เมตร, the heat generated when slitting with a straight knife may melt the polyethylene, making it difficult to unwind, or even tear the film.
The protective film can generally be stored for 12 months at a room temperature of 30°C and with no direct sunlight.
The higher the temperature, the shorter the storage period. For every 10°C higher, the storage period will be reduced by half.
3. Use of protective film
โดยทั่วไป, there is a curved roll (Banana roll) on the โต๊ะที่รองรับการอัดรีดระหว่างแม่พิมพ์และโต๊ะหมด to open the protective film to avoid bubbles and wrinkles.
For a low-viscosity protective film, the lower the tension when it is unwound, the better it will be, มิฉะนั้น, the edges will be warped.
The filming temperature should be higher than 10°C, and the tearing temperature should also be higher than 10°C.
The peeling force is closely related to the speed and angle of the tearing film.
Too low a temperature will harden the protective film and warp the edges.
In this case, apply hot air to heat first, or produce in an air-conditioned workshop.
The hardness of the rubber pressure roller is generally 60A.
When the protective film is rewinding, more or less air is wrapped in the adhesive, causing the rubber surface to be slightly uneven.
If the rubber pressure roller is too soft, it will not be able to effectively drive out the air bubbles and flatten the adhesive.
If the rubber pressure roller is too hard, the pressure generated will not be enough to make the glue and aluminum profile effectively contact, and it is easy to cause the edge of the protective film when edge cutting.
Since the rubber pressure roller will gradually age and harden during use, the rubber roller should be checked and replaced frequently.
4. Application of protective film in aluminum industry
The protective film is a layer of plastic film sticking to the aluminum material.
The purpose is to protect the surface of aluminum profile from damage during a series of processes such as handling, storage, transportation, กำลังประมวลผล, and installation.
After the aluminum profile is installed, the engineering team tore it off, so that the surface of the aluminum profile is as smooth as new, and it has the desired decorative effect.
โปรไฟล์อลูมิเนียมมีหลายประเภทในท้องตลาด, และเทคโนโลยีการรักษาพื้นผิวของวัสดุอลูมิเนียมได้รับการปรับปรุงอย่างต่อเนื่อง.
เทคโนโลยีการปรับสภาพพื้นผิวอะลูมิเนียมหลายชนิดรวมถึงการขัดเงาด้วยกลไก, ขัดเคมี, อโนไดซ์, การวาดภาพด้วยไฟฟ้า, สีเคมี, การฉีดพ่นฟลูออโรคาร์บอน, เคลือบผงไฟฟ้าสถิต, การรักษาด้วยการระเหิดของลายไม้, T ของสายการผลิตการอัดรีดโปรไฟล์อลูมิเนียม.
ต้องเลือกพื้นผิวโปรไฟล์อลูมิเนียมที่แตกต่างกัน ฟิล์มป้องกันแบบมีกาว.
ผลิตภัณฑ์ฟิล์มกันรอยโดยทั่วไปมี 4 ชุดความหนืดต่ำ, ความหนืดปานกลาง, ความหนืดสูงและความหนืดสูงเป็นพิเศษ; สีมีความโปร่งใส, สีขาวขุ่น, สีฟ้า, ดำและขาว, ค่าเสื่อมราคาอุปกรณ์; ความหนาคือ 30 ~ 200µm, ดังนั้นจึงจำเป็นต้องเลือกฟิล์มป้องกันที่แตกต่างกันตามพื้นผิวที่แตกต่างกันของโปรไฟล์อลูมิเนียม.
ตามพื้นผิวที่แตกต่างกันของโปรไฟล์อลูมิเนียมและแรงกดของฟิล์ม, the viscosity rise speed is different, โดยทั่วไป, the protective film should be left for enough time before peeling off the protective film to determine whether the viscosity is appropriate.
For a given surface, it is extremely important to choose the appropriate adhesive and viscous protective film.
The further processing steps are the key to determining the viscosity. The subsequent processing generally includes cutting, bending, drilling, stamping, T ของสายการผลิตการอัดรีดโปรไฟล์อลูมิเนียม.
โดยทั่วไป, low-viscosity protective films are used for smooth surfaces, such as mechanical polishing and chemical polishing aluminum profiles.
Medium-viscosity protective films are used for medium-rough surfaces, such as anodizing, electrophoretic coating, สีเคมี, การฉีดพ่นฟลูออโรคาร์บอน, and powder-coated aluminum profile.
Use high-viscosity protective film for very rough surfaces, such as electrostatic powder-coated aluminum profiles.
If laser cutting is required, because the protective film shrinks due to heat, you should use a super-high-viscosity protective film.
In addition to viscosity, users also need to test the tensile strength and elongation of the protective film to ensure that the flexibility and strength of the protective film can meet the requirements of the application.
5. บทสรุป
During transportation, storage, กำลังประมวลผล, and assembly of aluminum materials, the surface of aluminum profile needs to be protected to prevent harmful gases, microbial corrosion, dust pollution, mechanical scratches, scratching, ค่าเสื่อมราคาอุปกรณ์, so that the surface of the product retains the original high smoothness, improve the yield of secondary processing, in addition, it can also be used for temporary protection in electroplating, printing, coating, printing and dyeing, T ของสายการผลิตการอัดรีดโปรไฟล์อลูมิเนียม.
The most commonly used method to protect the surface of the aluminum profile is to put a protective film on the surface of the material to be protected.
The value of the protective film in the aluminum industry is very small, which is only an auxiliary material used by the manufacturer.
T ของสายการผลิตการอัดรีดโปรไฟล์อลูมิเนียม, if the protective film is used improperly or does not meet the requirements, the risk is that it will not only fail to protect, but may damage it.
The surface quality of the product brings tangible material loss and intangible brand image loss to users, which ultimately affects the product manufacturer’s price position and product sales.
The correct application of the protective film not only improves the appearance quality of aluminum profiles, facilitates material processing, increases the utilization rate of the material, and reduces the production cost of the product, but also improves the brand image of the company.
Brightstar Aluminum Machinery provides not only aluminum profile film sticking machine for our customers, but also aluminum profile packaging solution, อลูมิเนียม profiles automatic film applicator machine, hot shrink packaging machine, aluminum profiles wrapping machine and aluminum profiles bagging machine.
Contact us now for your aluminum profiles packaging solution! Completed solution and one-stop service!